Questions tagged [stereo]

Reproduction of an audio (stereophonics) or a video (stereoscopics) signals, through two separate channels.

Disambiguation:

  • Stereophonics - related to audio transmission, where an audio signal is "split" in two channels, typically right and left, since the intent is to give the human ears a sensation of multiple sources of sound.

  • Stereoscopic - Analog to stereophonic, but applied to images and video signals, with the intent to create 3D images.

107 questions
278
votes
3 answers

What is it that strips vocals from audio when a 1/8" audio jack is partially unplugged?

Every once in a while, my eighth-inch audio jack will slip loose and I'll seemingly lose only the voice part of a track -- leaving somewhat of a "karaoke" version. What I would guess about how audio plugs work suggests that I'd be making this up;…
editor
  • 2,521
  • 2
  • 15
  • 7
14
votes
3 answers

Accidentally downmixed stereo to mono, why does this work?

I have a cheap Chinese Bluetooth audio amplifier like this: It has four screw terminals for the speaker connections, namely L+, L-, R+ and R-. I accidentally connected a single speaker to L+ and R-, and was surprised to find that I could hear both…
Bas
  • 503
  • 1
  • 7
  • 17
10
votes
5 answers

Why is this 3-way speaker wired this way?

I found a service manual of a pair of 3-way speakers that were part of a mini integrated stereo system. These are Sony SS-H77 speakers, which have served me very well back in the day. Looking at the wiring diagram (below), there is something very…
ysap
  • 345
  • 4
  • 16
8
votes
1 answer

Using diodes to mix 2 audio signals into one set of speakers

I have the audio output of 2 computers connected to only one set of speakers. Each computer uses one of these external USB sound cards: And I use this splitter cable to wire the signals together: The whole thing works, but with some minor problems:…
GetFree
  • 489
  • 4
  • 7
  • 14
7
votes
1 answer

What is this component? In an Alpine 7903

I'm trying to replace some burnt up components on a old (and hard to find) car stereo for my project car. There are limited markings. One says BA RU and the other says DA RU
Joshua Galer
  • 89
  • 1
6
votes
2 answers

Raspberry Pi stereo camera frame synchronization/genlock (video or still image)

I need to frame synchronize a stereo camera for a computer vision application. The synchronization should the best possible, hopefully on a millisecond level. I would like to get about 10 FPS either as video or still images. Resolution requirement…
Kozuch
  • 481
  • 1
  • 7
  • 24
4
votes
1 answer

Volume control for power amplifier

Recently we installed some speakers into our church's ceiling. I've worked a little bit with analog circuits before, so I thought about putting a volume potentiometer before the amplifier. I don't know if this circuit will cause any issues with the…
ACEHOBOJOE
  • 45
  • 5
3
votes
4 answers

Volume gets lower when left and right audio channels are combined

I noticed that the volume of a speaker gets slightly lower when combining the left and right channels versus having ONLY one of the 2 channels connected to the speaker. I know that combining the left and right audio channels by simply soldering the…
Stelios L
  • 223
  • 4
  • 15
3
votes
1 answer

DIY Aux In connection to car stereo JVC KD-G151

I would like to connect my phone via jack cable (aux in) to my car stereo, which has no aux input (brand: JVC KD-G151). It is a CD player, so i wrote a silent disk to operate the cd player, and tried to figure out the connection points for the input…
davidszasz91
  • 31
  • 1
  • 2
3
votes
1 answer

Mono jack output to stereo headphones : how to send the mono signal to both sides?

I have a 3.5mm jack mono output. I'm plugging standard stereo headphones into this jack, and it plays only on one side. I want the sound to come out on both sides in the headphones (same signal, but in both ears). How can I cut and wire so that the…
sylbru
  • 149
  • 1
  • 1
  • 5
3
votes
2 answers

How can I synchronize the framerate of two webcameras. Is it even possible?

Pretext I am currently playing with stereo vision (two cameras capturing images simultaneously) for my robot hobby project. There are a few traits that is important when processing the images captured for stereo, and the most important of all is…
Mr. Developerdude
  • 337
  • 4
  • 16
2
votes
1 answer

Limiting current with an NPN for a 'safer' tube amplifier

Relatively new to electrical engineering broadly so please excuse any confusion, etc. Here to learn! I am working on the layout for a stereo direct coupled tube amplifier. The schematic (below) is by Nobu Shishido and while it was previously…
user2954453
  • 23
  • 5
2
votes
1 answer

Stereo line input & Mono Mixer

I’ve been searching for a module to mix a stereo line input from a laptop with a hot mono input from my Eurorack setup, while also maintaining a proper line output signal. I love the design of the BMC54 module by Barton Musical Instrument…
Alex Kulinchenko
  • 23
  • 2
2
votes
2 answers

I2S microphone data synchronization for left and right channel

I have I2S MEMS microphones (transmitters, stereo) in slave mode and a microcontroller in master mode. When the WS pin iw 0 (low) the data available on the SD pin is for the left channel (microphone 1.) When the WS pin is 1 (high) the data available…
CuriousByte
  • 21
  • 1
2
votes
0 answers

Summing Audio Channels

I’m trying to sum my car stereo output. Factory output has bass on one output and mid and tweeter on another output giving me 2 channels for left and 2 channels for right. Ideally I’d like to sum them together and would of used something like a PAC…
Phils Channel Various Stuff
  • 21
  • 1
1
2 3 4 5 6 7 8